Standard Plus STC Antifouling - 0.75 LT - 3E6411 - AEMME

Standard Plus STC Antifouling  - 0.75 LT - 3E6411 - AEMME:

Self-polishing antifouling formulated with copper thiocyanate, usable on all types of boats, including those in aluminum and light alloys. 

Recommended for medium-speed boats up to 30 knots. We recommend applying at least 2 coats of the product.

Available colors: White.

USAGE:

PREPARATION OF THE SUPPORT AND APPLICATION CYCLE: 

New iron fairings. 

Apply a coat of EPOFOND AM-9 on sandblasted iron at grades 2-2.5, allowing it to dry for 12-24 hours. 

Then apply 2 coats of EPOFOND AM-9 spaced no more than 24 hours apart (at least 6-8 hours), then 2 coats of STANDARD PLUS STC White antifouling 18-24 hours apart.

New wooden fairings:

Apply one coat of widely diluted EVIOX CROMOMINIO. 

Follow with two coats of SOLVER PRIMER leaving 24 hours between coats. Then apply 2 coats of STANDARD PLUS STC White antifouling at least 12-24 hours apart.

New hulls in fiberglass or plastic:

Degrease with detergents and water and rinse. 

Lightly sand with fine abrasive papers and dust. 

Apply a coat of EPOFOND AM-9 or POLIFIBER PRIMER and after 24 hours sand with fine sandpaper. 

Then apply with 2 coats of STANDARD PLUS STC Bianca 12-24 hours apart.

Hulls in aluminum or light alloys:

Degrease the surface thoroughly with Thinner 765. Then apply a coat of EPOFOND AM-9 and let it dry for 8 hours but not more than 24 hours. 

Apply 3 coats of SOLVER PRIMER 24 hours apart, then 2 coats of STANDARD PLUS STC White antifouling 12-24 hours apart.

Fairings already painted:

- If the old antifouling is in good condition, compatible, and well-anchored, it will be sufficient to apply one or two coats of SOLVER PRIMER before overcoating with 2 coats of STANDARD PLUS STC White antifouling at a distance of at least 12-24 hours between one coat and the 'other.

- If the old antifouling is not in good condition, restore the substrate by removing the residues of the old paint with a scraper or brush and then proceed as recommended for new hulls.

Recommendations:

The maximum period of commissioning of the antifouling, after the application of the last coat, is 1 month; with top-of-the-range products based on copper oxide and upon agreement with our technical personnel, the same can extend up to 3 months, provided that the hull is protected from humidity, rain, or atmospheric agents, with plastic or similar material.

Color:

The color of the antifouling after immersion may undergo a slight variation. There may be small differences in color between different production batches: in this case, mix them before application.

Remarks.

The values ​​indicated in this technical data sheet may undergo slight variations from one product to another. The applied product must not be put in contact with water, or chemical products or subjected to mechanical stress before complete crosslinking. The thicknesses of the wet film are intended for the undiluted product. With dilution, this value will increase. The above information is the result of accurate laboratory tests and practical experiences, however, given that the product is mainly used outside the manufacturer's control, the same can only guarantee its continuous quality. The information contained in this sheet may be subject to review by the Company. For clarifications, updates, or further information it is advisable to contact the manufacturer directly.

SAFETY PRECAUTIONS

Before starting the application of the paint products, carefully observe the risk symbols and the safety rules shown on the label of each jar and on the Safety Data Sheet of each product available on request. For further information do not hesitate to contact our Technical Department.

NOTE:

The information contained herein is provided to the best of our current knowledge, however as the conditions of use of our products are beyond our control, such information does not constitute any kind of implied warranty; in this sense, the supplier company declines from now on any responsibility that may be connected to an anomalous use of the products. The Technical Department of its headquarters is available for any clarification related to the use of our products. The percentages of dilution and drying times are to be considered only indicative, in relation to a temperature of 20 ° C, and are therefore subject to variations with the variation of the temperature, in the presence of particular climatic conditions or application factors determined at the time of 'application.